DuctlessWise DIY mini splits and heat-pump water heaters, sized right
Setup & Care

How to Flush a Tankless Water Heater (and How Often)

Tankless water heater maintenance: how often to flush by hardness, what a flush kit includes, vinegar vs descaler, the manual's steps and when to call a pro.

How to Flush a Tankless Water Heater (and How Often)
The short answer Flush a tankless water heater once a year if your water is moderately hard or hard (about 4 to 9 grains per gallon) and untreated, per Navien's manual; soft water under 4 grains needs no flushing. A flush circulates white vinegar or a tankless descaler through the heat exchanger with a small pump for at least 45 minutes, with the unit off.

Scale is the main reason tankless water heaters lose flow and throw error codes. Hard water leaves calcium and magnesium on the hot surfaces of the heat exchanger, and a yearly flush dissolves it before it builds up. This guide follows the manufacturer’s manual: the schedule, the gear, the steps, and the points where a homeowner should stop and call a plumber.

How often should you flush a tankless water heater?

Your water hardness sets the schedule. Navien’s NPE-2 installation manual gives this table for homes without a water softener or scale-prevention device:

Water hardnessGrains per gallon (mg/L)TreatmentFlush frequency (homes)
Soft0-4 (0-60)NoneNone
Moderately hard4-7 (61-120)Softener or scale prevention recommendedOnce a year
Hard7-9 (121-160)Softener or scale prevention recommendedOnce a year
Very hard9-12 (161-200)Softener or scale prevention highly recommendedFollow the manual
Extremely hardOver 12 (over 200)Treatment requiredTreat the water first

Navien’s maximum allowed hardness for the heater is 200 mg/L (12 grains per gallon). HomeGuide’s general water heater advice is similar: at least once a year, every 6 months on hard water. Find your number on your utility’s annual water quality report or with a test strip.

Navien heaters can also remind you. The installer can set a descaling reminder at 6, 12 or 24 months, and an E760 code on the display is the flushing and service alarm.

What do you need to flush a tankless water heater?

You need a pump loop and a way to connect it. Navien’s manual lists a bucket of 5 gallons or larger, the cleaning solution, 3 hoses and a small water circulation pump. A tankless flush kit is simply those parts sold together, so check that its hoses fit your heater’s service ports.

The heater also needs service valves. These are isolation valves on the hot and cold lines next to the unit, each with a small hose port and a shut-off; Navien sells them as a valve kit. They let you close off the house plumbing and loop the solution through the heater alone.

If your heater was installed without service valves, the flush cannot be done the standard way. Adding them is plumbing work for a licensed plumber, and it is worth doing once so every future flush is a one-hour job.

Should you use vinegar or a descaler?

Use what your manual allows. Navien’s manual says to flush with white vinegar or solutions specifically formulated for tankless water heaters. Vinegar is cheap and widely used; a packaged descaler is usually faster on heavy scale and comes premeasured.

Other manufacturers word this differently, and some name their own product. Do not use anything the manual does not list, do not mix cleaners, and dilute a concentrate exactly as its label says. After a descaler, the fresh-water rinse matters: the goal is to flush every trace of solution out of the heat exchanger before the heater supplies the house again.

How do you flush a tankless water heater, step by step?

The steps below summarize Navien’s owner procedure for its NPE-2 condensing units. Valve names and order differ by brand, so read your own manual first and follow it where it differs. Navien itself calls the flush somewhat complicated and says to contact a licensed professional if you are unsure of any step.

  1. Turn the heater off at its power button and disconnect its power supply. Navien’s draining procedure also closes the gas valve; closing it for the flush is the cautious choice.
  2. Close the main hot and cold service valves so the heater is isolated from the house.
  3. Connect one hose from the hot-side service port to the bucket.
  4. Connect a hose from the pump outlet to the cold-side service port, and put the pump inlet hose in the bucket.
  5. Pour the cleaning solution into the bucket, open both service ports and start the pump.
  6. Let the solution circulate for at least 45 minutes.
  7. Rinse: move the drain hose from the bucket to a floor drain or laundry tub, close the cold-side service port, open the cold supply valve and let fresh water flow through for 5 minutes.
  8. Close the hot-side service port and open the hot supply valve.
  9. Disconnect the hoses, then clean the cold water inlet filter (next section).
  10. Restore power, reopen the gas valve if you closed it, and turn the heater on.

Run a hot tap afterward until the flow is steady and any air has cleared from the lines.

How do you clean the inlet water filter?

Clean it every time you flush, and any time hot water flow drops. The cold water inlet filter is a small screen at the heater’s cold inlet that catches grit before it reaches the heat exchanger. Navien’s manual has you drain the heater, remove the filter, rinse it under cold running water, scrub it with a brush if needed, and screw it back in tightly.

Navien’s troubleshooting table checks this filter first when no hot water comes out or the water runs cold. The manual also asks owners to clean the combustion air intake filter every 3 to 4 months; a clogged intake filter stops the heater and shows error code E110. Both are quick jobs that most maintenance guides skip.

What are the signs a tankless water heater needs flushing?

The heater usually tells you. Watch for:

  • Overheating error codes. Navien points E016 (heat exchanger overheating) and E030 (exhaust overheating) to a clean inlet filter and a heat exchanger flush.
  • A service alarm. E760 on Navien units is the flushing and service reminder.
  • Falling hot water flow or temperature swings that a clean inlet filter does not fix.
  • It has been a year or more on moderately hard or hard water with no treatment.

If an error returns after a flush, a filter clean and the remedy your manual’s error table lists, stop there. Navien’s table sends codes such as E031 (burner overheating) and E046 (limit control) straight to technical support.

How much does a tankless flush cost, DIY vs pro?

A professional tankless flush costs $150 to $350, according to HomeGuide’s May 2024 cost guide, which notes that the job takes longer than a tank flush because the descaler has to circulate through the heater with a pump. Doing it yourself costs the solution each year plus a one-time pump, hose and bucket kit.

Over the life of the heater the difference is large: 15 yearly pro flushes come to $2,250 to $5,250, enough to change whether tankless beats a tank on cost. Our tankless vs tank comparison runs that 15-year math, and the tankless water heater cost guide covers the purchase side.

Does flushing protect your warranty?

It is part of keeping it. Navien gives its residential NPE heat exchanger a 15-year warranty, but the warranty is void for failure to perform regular maintenance, and it excludes damage caused by hard water deposits and lime or mineral buildup. The installation manual adds that damage from poor water quality is not covered.

Read the rest of the exclusions before you buy, too. Navien’s warranty is also void for installation by a non-licensed installer and for units bought online or from a seller Navien has not authorized. Keep receipts for the heater, the installation and each flush or service visit.

Can a water softener replace flushing?

On Navien’s schedule, largely yes. The manual recommends flushing when a treatment device is not installed, and it recommends a softener or a scale-prevention system from 4 grains per gallon up, requiring one above 12 grains. A working softener removes the hardness that forms scale.

Keep cleaning the inlet filter and watching for error codes either way, since sediment and other water quality problems still reach the heater. If you are still deciding between heater types and your water is very hard, a heat pump water heater needs a different kind of upkeep; our heat pump vs tankless comparison sets the two side by side.

When should you stop and call a plumber?

Call a licensed plumber, or the installer, instead of continuing when:

  • The heater has no service valves, or a valve leaks or will not close.
  • You smell gas. Leave the house and call the gas utility from outside.
  • An error code returns after a flush and an inlet filter clean.
  • The job means opening the sealed parts of the unit: burner, gas valve, venting or wiring.
  • Water leaks from the heater itself, not from a hose connection.

A flush is owner maintenance only when the manual says so and the heater was installed with the valves to do it. Everything on the gas, vent and electrical side stays with licensed pros under local code.

Where do these numbers come from?

  • Navien NPE-2 User’s Information Manual and NPE-2 Installation and Operation Manual (navieninc.com downloads, read October 6, 2026): flush procedure and supplies, water quality limits, hardness schedule, descaling reminder, error codes, inlet and intake filters, warranty terms.
  • HomeGuide, water heater flush cost, May 20, 2024: professional flush prices and frequency advice.

Frequently asked questions

Quick answers to what readers ask us most

How often should a tankless water heater be flushed?

It depends on hardness. Navien's manual says no flushing for soft water (0 to 4 grains per gallon) and once a year for 4 to 9 grains in homes without a softener or scale-prevention system. Above 12 grains it requires water treatment.

Can I use vinegar to flush a tankless water heater?

Navien's manual allows white vinegar or a solution made for tankless water heaters. Other brands may name a specific product, so check your own manual first and use only what it lists.

How long does it take to flush a tankless water heater?

Plan on about an hour and a half. Navien's procedure circulates the solution for at least 45 minutes and then rinses with fresh water for 5 minutes; setup, cleaning the inlet filter and restarting take the rest.

What happens if you never flush a tankless water heater?

Scale coats the heat exchanger, cutting flow and causing overheating faults. Navien's error table points codes such as E016 (heat exchanger overheating) to a filter clean and a flush, and its warranty excludes damage from hard water deposits.

How much does it cost to have a tankless water heater flushed?

HomeGuide's May 2024 cost guide puts a professional tankless flush at $150 to $350. Doing it yourself costs the solution plus a one-time pump, hose and bucket kit, if your heater has service valves.

Can I flush a tankless water heater without isolation valves?

Not with the standard method. The flush connects hoses to service ports on the hot and cold lines next to the heater. If yours has none, have a licensed plumber add an isolation valve kit first.